--------------5D4533993265CD9B49E324F9
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
hello from france, any help ?? THANKS A LOT
Here are the trace : dmesg, network start , insmod, rtldiag, lspci -vv :
SEEMS that eth0 can not be mounted!!
--------------------------------------------
Linux version 2.2.5-15 (gcc version egcs-2.91.66 19990314/Linux
(egcs-1.1.2 release)) #1 Mon Apr 19 23:00:46 EDT 1999
PCI: PCI BIOS revision 2.10 entry at 0xfdb91
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086,
DID=2411
PCI_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
------------------------------------------------
[root@chavignol init.d]# ./network start
Bringing up interface lo [ OK ]
Bringing up interface eth0
Delaying eth0 initialization. [ FAILED ]
-------------------------------------------------
[root@chavignol /tmp]# insmod rtl8139.o
rtl8139.o: unresolved symbol pci_drv_unregister
rtl8139.o: unresolved symbol pci_drv_register
----------------------------------------------
[root@chavignol /tmp]# ./rtl8139-diag -aa
rtl8139-diag.c:v2.00 4/19/2000 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a SMC1211TX EZCard 10/100 (RealTek RTL8139) adapter at
0xcc00.
RealTek chip registers at 0xcc00
0x000: 67b51000 0000b47b 80004000 00000000 00002000 00002000 00002000
00002000
0x020: 013b4000 013b7000 013b6000 013b5000 00003000 01000000 0000fff0
00000000
0x040: 78000000 00000000 a1feddb1 00000000 000d14c6 00000000 0084e108
00100000
0x060: 1000000f 05e1782d 00000000 00000000 00000005 000f77c0 58fab388
ad38d843.
No interrupt sources are pending.
The chip configuration is 0x14 0x0d, MII half-duplex mode.
EEPROM size test returned 6, 0x204a4 / 0x2.
-----------------------------------------------
lspci -vv :
01:05.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX
(rev 10)
Subsystem: Unknown device 1113:9211
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 min, 64 max, 64 set
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at cc00
Region 1: Memory at e8000000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--------------5D4533993265CD9B49E324F9
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
<!doctype html public "-//w3c//dtd html 4.0 transitional//en">
hello from france, any help ?? THANKS A LOT
Here are the trace : dmesg, network
start , insmod, rtldiag, lspci -vv :
SEEMS that eth0 can not be mounted!!
--------------------------------------------
Linux version 2.2.5-15 (gcc version egcs-2.91.66 19990314/Linux
(egcs-1.1.2 release)) #1 Mon Apr 19 23:00:46 EDT 1999
PCI: PCI BIOS revision 2.10 entry at 0xfdb91
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086,
DID=2411
PCI_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA,
hdb:pio
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA,
hdd:pio
------------------------------------------------
[root@chavignol init.d]# ./network start
Bringing up interface lo
[ OK ]
Bringing up interface eth0
Delaying eth0 initialization.
[ FAILED ]
-------------------------------------------------
[root@chavignol /tmp]# insmod rtl8139.o
rtl8139.o: unresolved symbol pci_drv_unregister
rtl8139.o: unresolved symbol pci_drv_register
----------------------------------------------
[root@chavignol /tmp]# ./rtl8139-diag -aa
rtl8139-diag.c:v2.00 4/19/2000 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a SMC1211TX EZCard 10/100 (RealTek
RTL8139) adapter at 0xcc00.
RealTek chip registers at 0xcc00
0x000: 67b51000 0000b47b 80004000 00000000 00002000 00002000
00002000 00002000
0x020: 013b4000 013b7000 013b6000 013b5000 00003000 01000000
0000fff0 00000000
0x040: 78000000 00000000 a1feddb1 00000000 000d14c6 00000000
0084e108 00100000
0x060: 1000000f 05e1782d 00000000 00000000 00000005 000f77c0
58fab388 ad38d843.
No interrupt sources are pending.
The chip configuration is 0x14 0x0d, MII half-duplex mode.
EEPROM size test returned 6, 0x204a4 / 0x2.
-----------------------------------------------
lspci -vv :
01:05.0 Ethernet controller: Accton Technology
Corporation SMC2-1211TX (rev 10)
Subsystem: Unknown device 1113:9211
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 min, 64 max, 64 set
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at cc00
Region 1: Memory at e8000000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-