D-Link DFE-660

Ralf Lammers rlammers@matzner.de
Thu Jun 24 09:01:29 1999


--ELM930228856-33618-0_
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: 7bit

Hi folks,

does anyone know anything about the D-Link DFE-660 PCMCIA network adapter?
Well, I tried to use it with the tulip driver, but it does not seem to
work. The Linux cardmgr recognizes the Card and automatically loads
the tulip_cb module. But ifconfig only display the H/W address
00:80:00:80:00:80 which is definity wrong. The debug-utility 'tulip-diag -e'
shows the correct one. Do you think it's because the D-Link card is an 32bit
PCMCIA-adapter? I read that this sometime cases problems.

BTW, I'm running Kernel version 2.2.9 including pcmcia-cs version 3.0.11.
I also installed your latest version of tulip.c (v0.91e).

Any help would be greatly appreciated.
Thanks in advance,
Ralf
-- 
Dipl.-Phys. Ralf Lammers / Head of Computer Dept. Phone:  +49 (0)541 59905-40
Horst Matzner Fertigungstechnik GmbH & Co. KG     Fax:    +49 (0)541 59905-79
Industriestrasse 28                               E-Mail: rlammers@matzner.de
D-49082 Osnabrueck, Germany                       WWW:    http://www.matzner.de
_______________________________________________________________________________
"We must fall back on the old axiom that when other contingencies fail whatever
 remains - however improbable - must be the truth."  (Lt. Cmdr. Data in ST:TNG)

--ELM930228856-33618-0_
Content-Type: text/plain; charset=US-ASCII
Content-Disposition: attachment; filename=tulip-diag-a
Content-Description: tulip-diag-a
Content-Transfer-Encoding: 7bit

tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Digital DS21143 Tulip chip registers at 0x400:
  f9a04800 ffffffff ffffffff 0043f010 0043f210 f0120000 b2420200 fbfffbff
  e0000000 ffffcbf8 ffffffff 00000000 000010c6 ffff0001 fffbffff 8ffb0008
 Port selection is 10mpbs-serial, full-duplex.
 Transmit stopped, Receive stopped, full-duplex.
  The Rx process state is 'Reading a Rx descriptor'.
  The Tx process state is 'Reading a Tx descriptor'.
  The transmit threshold is 72.

--ELM930228856-33618-0_
Content-Type: text/plain; charset=US-ASCII
Content-Disposition: attachment; filename=tulip-diag-e
Content-Description: tulip-diag-e
Content-Transfer-Encoding: 7bit

tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
 Port selection is 10mpbs-serial, full-duplex.
 Transmit stopped, Receive stopped, full-duplex.
  The Rx process state is 'Reading a Rx descriptor'.
  The Tx process state is 'Reading a Tx descriptor'.
  The transmit threshold is 72.
Ethernet MAC Station Address 00:80:C8:8F:43:EA.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
 1 transceiver description blocks:
  Media MII, block type 3, length 13.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 0 words:.
   21143 MII reset sequence is 0 words:.
    Media capabilities are 7800, advertising 01e1.
    Full-duplex map 5000, Threshold map 1800.
    MII interrupt on GPIO pin -1.
 MII PHY found at address 0, status 0x7809.
 MII PHY #0 transceiver registers:
   3000 7809 0040 6212 01e1 0000 0000 0000
   0000 0000 0000 0000 0000 0000 0000 0000
   1000 0000 0000 0000 0000 0000 0400 0000
   003c 1002 0f00 ff00 002c 0000 0010 000b.

--ELM930228856-33618-0_
Content-Type: text/plain; charset=US-ASCII
Content-Disposition: attachment; filename=tulip-diag-m
Content-Description: tulip-diag-m
Content-Transfer-Encoding: 7bit

tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
 Port selection is 10mpbs-serial, full-duplex.
 Transmit stopped, Receive stopped, full-duplex.
  The Rx process state is 'Reading a Rx descriptor'.
  The Tx process state is 'Reading a Tx descriptor'.
  The transmit threshold is 72.
 MII PHY found at address 0, status 0x7809.
 MII PHY #0 transceiver registers:
   3000 7809 0040 6212 01e1 0000 0000 0000
   0000 0000 0000 0000 0000 0000 0000 0000
   1000 0000 0000 0000 0000 0000 0500 0000
   003c 1002 0f00 ff00 002c 0000 0010 000b.
  Internal autonegotiation state is 'Transmit disabled'.

--ELM930228856-33618-0_--