tulip driver in lunix red hat 6.0 for DFE-570TX

Steve Skworchewski steve@munic.kurgan.ru
Fri Aug 13 02:27:21 1999


Hi!

I has installed the network charge D-Link DFE-570TX on my SMP (two
processors PII 450) server.
The Operating system Linux Red Hat 6.0.
Linux its has defined orderly and has loaded the module tulip.o.
My network uses 10BaseT UTP, but adapter does not want to close at velocity 10Mb.
Use options=0 or 9 or 11 or 12 not give results.
The Adapter is fixed on velocity 100Mb.

See log:
Aug 13 10:09:01 linux kernel: tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
Aug 13 10:09:01 linux kernel: eth0: Digital DS21142/3 Tulip at 0xc800, 00 80 c8 f8 6b c4, IRQ 5.
Aug 13 10:09:01 linux kernel: eth0:  EEPROM default media type Autosense.
Aug 13 10:09:01 linux kernel: eth0:  MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Aug 13 10:09:01 linux kernel: eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
Aug 13 10:09:01 linux kernel: eth0:  MII transceiver found at MDIO address 1, config 3100 status 7849.
Aug 13 10:09:01 linux kernel:   PCI latency timer (CFLT) is 0x20,  PCI command is 0017.
Aug 13 10:09:01 linux kernel: eth1: Digital DS21142/3 Tulip at 0xc400, 00 80 c8 f8 6b c5, IRQ 9.
Aug 13 10:09:01 linux kernel: eth1:  EEPROM default media type Autosense.
Aug 13 10:09:01 linux kernel: eth1:  MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Aug 13 10:09:01 linux kernel: eth1:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
Aug 13 10:09:01 linux kernel: eth1:  MII transceiver found at MDIO address 1, config 3100 status 7849.
Aug 13 10:09:01 linux kernel:   PCI latency timer (CFLT) is 0x20,  PCI command is 0017.
Aug 13 10:09:01 linux kernel: eth2: Digital DS21142/3 Tulip at 0xc000, 00 80 c8 f8 6b c6, IRQ 11.
Aug 13 10:09:01 linux kernel: eth2:  EEPROM default media type Autosense.
Aug 13 10:09:01 linux kernel: eth2:  MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Aug 13 10:09:01 linux kernel: eth2:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
Aug 13 10:09:01 linux kernel: eth2:  MII transceiver found at MDIO address 1, config 3100 status 7849.
Aug 13 10:09:01 linux kernel:   PCI latency timer (CFLT) is 0x20,  PCI command is 0017.
Aug 13 10:09:01 linux kernel: eth3: Digital DS21142/3 Tulip at 0xb800, 00 80 c8 f8 6b c7, IRQ 10.
Aug 13 10:09:01 linux kernel: eth3:  EEPROM default media type Autosense.
Aug 13 10:09:01 linux kernel: eth3:  MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Aug 13 10:09:01 linux kernel: eth3:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
Aug 13 10:09:01 linux kernel: eth3:  MII transceiver found at MDIO address 1, config 3100 status 7869.
Aug 13 10:09:01 linux kernel:   PCI latency timer (CFLT) is 0x20,  PCI command is 0017.
Aug 13 10:11:00 linux kernel: eth0: 21142 negotiation status 000020c6, 10baseT.
Aug 13 10:11:00 linux kernel: eth0: 21142 negotiation failed, status 000020c6.
Aug 13 10:11:00 linux kernel: eth0: Testing new 21142 media 100baseTx.
Aug 13 10:11:00 linux kernel: eth0: The transmitter stopped!  CSR5 is f0678006, CSR6 b3862002.

How I this correct?

See you. Steve