power consumption
Many of your questions may have already been answered in earlier discussions or in the FAQ. The search results page will indicate current discussions as well as past list serves, articles, and papers.
Jim Lux James.P.Lux at jpl.nasa.govTue Feb 20 17:44:51 PST 2001
- Previous message: Beowulf digest, Vol 1 #279 - 12 msgs
- Next message: Correct URL for formfactor and power supply data...
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
There is a lot of power consumption data for various form factors at the Intel web site.(I think it is http://www.teleport.com/~ffsupport/ ) The ATX/ATX12V Power Supply Design Guide on that site gives the following "typical" power distribution for a 160W ATX configuration: +12V 0-6A, 8A pk (most likely when hard drives spin up, or floppy seeks...) +5V 1-18A +3.3V 0.3-14A -5V 0-0.3A -12V 0-0.8A +5 VSB 0-1.5A, 2.5A pk They have a nifty little chart showing that the combined +5 and +3.3 loads share power rating with the 12V. If you draw the full 72W of 12V, you can only draw about 30-75W from the lower voltages. For 200W, 250 and 300W configurations the powers increase a bit: +12V, 8/10,10/12, 12/14 (max/pk) +5V, 21,25,30 +3.3V,14,16,20 The spec requires 68% efficiency (which, by the way, is pretty bad), with some other stuff for "Energy Star" operation A better guide may be the FlexATX thermal design document, also from Intel.. (This doc has a lot of useful information on airflow and temps within typical tower cases, etc.) Processor <=40W Chipset/Graphics 3W SDRAM 8W Mobo Misc 5W Slot #5, PCI card 5W Mobile CD ROM 5W HardDrive 8W (7.2krpm, idling) Subtotal 74W (DC) Pwr Supply 32W (assumes 70% efficiency) Total AC 106W All temps are specified as Tamb<=55C, except processor at Tinlet = 40C Another document (MicroATX) mentions 60W for the processor, 11W for the voltage regulator, 12W for AGP graphics, etc. for a total DC power of 131W -----Original Message----- From: pbn2au <pbn2au at qwest.net> To: beowulf at beowulf.org <beowulf at beowulf.org> Date: Tuesday, February 20, 2001 5:13 PM Subject: Re: Beowulf digest, Vol 1 #279 - 12 msgs >Hello, > > Just a question, a thought that came up during the shelves discussion. Does any body have a >web site or other information that would provide me a guess at how many, and what kinds of >motherboards I could connect to a single 250W power supply? > > For instance: A super micro P5STE Running a P 200, 1 floppy drive, a fan and a nic card. Also >figure for 64, 128, and 256 meg ram.. > > Power is not cheap but I am! The configuration sets in an old rack mount , and has 8 fans to >cool it. Stop laughing and think about it. > >Dave > > > > >_______________________________________________ >Beowulf mailing list, Beowulf at beowulf.org >To change your subscription (digest mode or unsubscribe) visit http://www.beowulf.org/mailman/listinfo/beowulf >
- Previous message: Beowulf digest, Vol 1 #279 - 12 msgs
- Next message: Correct URL for formfactor and power supply data...
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
More information about the Beowulf mailing list
